Bando RPF5990 Auto RPF Raw Edge Cogged 14MBando RPF5990 Molded notch design gives extra flexibility to reduce heat build up and provide long belt life, especially on small pulleys. Oil and heat resistant rubber impregnated fabric is extra flexible to reduce heat build up and prevent cracking Strong tensile cord is engineered and treated to carry high horsepower loads without stretching. Retains tension to reduce maintenance. Tough fiber reinforces rubber protects and stabilizes the tensile
D5530R FR LC 2812ATZ ENCL
Standard IEC 60034-1 Frequency 50 Hz Voltage 380-415/660//460 V Number of poles 6 Degree of Protection IP55 Synchronous speed 1000 rpm Output rating 2
Special Software Pump Genius Multiplex Line Voltage 380-480V Output Amps 3~ Line Frequency 50/60Hz Output Voltage 0 - Net Output frequency 0-300Hz ND Output Amps 38A HD Output Amps 33A ND Amps 60s 41
6 a Front Face Code Standard Front Shaft Indicator None Heater Indicator No Heater Insulation Class H Inverter Code Inverter Ready KVA Code J Lifting Lugs No Lifting Lugs Locked Bearing Indicator Locked Bearing Motor Lead Exit Ko Box Motor Lead Termination Flying Leads Motor Lead Quantity/Wire Size 9 @ 16 AWG Motor Type 3640M Mounting Arrangement F1 Number of Poles 4 Overall Length 16
468 Line Amps 4
Bando - 10-3V730 To resolve problem applications where belts are flipping over or jumping out of the sheaves
6 A Number of poles 3 Short-circuit release 13 x Iemax Rated operational voltage Ue 690 V Rated operational frequency 50/60 Hz Rated insulation voltage Ui 690 V Rated impulse withstand voltage Uimp 6 kV Utilization category - IEC60947-2 (motor starter protector/circuit breaker) A Utilization category - IEC60947-4-1 (Motor Starters) AC-3 Trip test Yes Overload protection Yes Phase failure sensitivity Yes Trip indication No Tripping class 10 Maximum operating frequency (ops
7 POLES 4 NUMBER SPEEDS 1 RPM 1760 RPM 2 1760 RPM 3 1755 RPM 4 1455 RPM 5 1455 HERTZ 60 HERTZ 2 50 VOLTS PRIMARY 230/460 VOLTS 460 VOLTS 2 230 VOLTS 3 208 VOLTS 4 400 VOLTS 5 200 FRME 143 SHAFT CODE T MOUNTING HORZ-FOOTED ASSEMBLY POSITION F1 MOTOR TYPE TCE OPPOSITE END BEARING 6203-J/C3 SHAFT END BEARING 6205-J/C3 AMBIENT 40 ROTATION DUAL SERVICE FACTOR 1
Bando - 8C120 To resolve problem applications where belts are flipping over or jumping out of the sheaves
39K057X101G1 HP 20 RPM 3510 VOLTS 230/460 AMPS 47/23
625 IN Shaft Extension Location Pulley End Shaft Ground Indicator No Shaft Grounding Shaft Rotation Reversible: Connected Standard Shaft Slinger Indicator Shaft Slinger Speed 1770 rpm Speed Code Single Speed Motor Standards NEMA Starting Method Direct on line Thermal Device - Bearing None Thermal Device - Winding Normally Closed Thermostat Vibration Sensor Indicator No Vibration Sensor Winding Thermal 1 None Winding Thermal 2 None Drawings
3 a Front Face Code Standard Front Shaft Indicator None Heater Indicator No Heater Insulation Class H Inverter Code Inverter Ready KVA Code K Lifting Lugs Standard Lifting Lugs Locked Bearing Indicator Locked Bearing Motor Lead Exit Ko Box Motor Lead Termination Flying Leads Motor Lead Quantity/Wire Size 3 @ 16 AWG Motor Type 3636M Mounting Arrangement F1 Number of Poles 4 Overall Length 18
